How do I decode an Air Temperature and Humidity event?

How do I decode an Air Temperature and Humidity event?

The Air Temperature and Humidity Sensor will generate events when the environment changes to exceed set thresholds or on a periodic basis.

Air Temperature and Humidity Event Message: 0x0D
      Byte                        Description
      0                              Temperature/Humidity Event Payload
      1                               Current temperature in degrees Celsius with sign bit
      2                              First decimal of current temperature (0-9) in the most significant 4-bits.
      3                              Humidity in % relative humidity (0-100%)
      4                              First decimal of relative humidity (0-9) in the most significant 4-bits.

Air Temperature and Humidity Event Payload Definitions
      Event Payload      Description
      0x00      Periodic report
      0x01                       Temperature has risen above upper threshold
      0x02      Temperature has fallen below lower threshold
      0x03      Temperature report on change increase
      0x04      Temperature report on change decrease
      0x05      Humidity has risen above upper threshold
      0x06      Humidity has fallen below lower threshold
      0x07      Humidity report on change increase
      0x08      Humidity report on change decrease

Example of Air Temperature and Humidity Event Message:

      1 0 0D 05 17 70 3D 80

      1             Protocol Version (currently always 0x1)
      0      Packet Counter (increments by 1 each message and wraps from 0xF to 0x0)
      0D     Message Type Code (Air Temp & Humidity Event = 0x0D)
      05     Event (Humidity has risen above upper threshold = 0x05)
      17     Current temperature in degrees Celsius (23 = 0x17)
      70          First decimal of current temperature (7 = 0x70)
      3D     Humidity in % relative humidity (61 = 0x3D)
      80     First decimal of relative humidity (8 = 0x80)

The RadioBridge Console will generate the following output for this message:

      Humidity has risen above upper threshold
      Current temperature in degrees Celsius: 23.7 
      Humidity in % relative humidity: 61.8

    • Related Articles

    • How do I decode an Air Temperature and Humidity event?

        The Air Temperature and Humidity Sensor will generate events when the environment changes to exceed set thresholds or on a periodic basis.   ​ Byte 0: 7-4 Byte 0: 3-0 Byte 1 Byte 2          Byte 3     Byte 4   Byte 5 Byte 6 Protocol version   (4 ...

    • How do I encode a Configuration Downlink for an Air Temperature and Humidity Sensor?

      NOTE: All downlinks must contain a total of (8) bytes, padded with zeros at the end when necessary. See User Manual at https://www.multitech.com/brands/reveal-wireless-air-temp-humidity-sensors for more information. Threshold Mode Configuration ...

    • How Do I Decode a No-Probe Temperature Sensor Event

      The No-Probe Temperature Sensor will generate events if the temperature rises above or falls below the configured thresholds   Byte 0: 7-4 Byte 0: 3-0 Byte 1 Byte 2    Byte 3 Byte 4 Protocol version     (4 bits) Counter       (4 bits) No-Probe Temp ...

    • How do I decode an External Probe Temperature Sensor Event?

      The External Probe Temperature Sensor will generate events if the temperature rises above or falls below the configured thresholds.   Byte 0: 7-4 Byte 0: 3-0 Byte 1 Byte 2    Byte 3 Byte 4 Protocol version     (4 bits) Counter       (4 bits) ...

    • How do I decode a Thermocouple Temperature Sensor event?

      The Thermocouple Temperature Sensor will generate events based on temperature measurements rising above or falling below configured thresholds, report-on-change, and periodic messaging.   Byte 0: 7-4 Byte 0: 3-0 Byte 1 Byte 2 Byte 3  and Byte 4 Byte ...